|
Fluke 90i-610s 1A to 600A AC/DC Current Probe
|
|
Current Range: 1 to 600 A DC or AC Peak
Basic Accuracy (DC to 400 Hz): +/- (2% of reading + 1 A)
Output Signal: 100 A range: 10 mV/A | 600 A range: 1 mV/A
Frequency Range: 40 Hz to 400 Hz
Working Voltage: 600 V AC rms
Maximum Conductor Diameter: 34 mm (1.34 inch)
Safety Rating: IEC 1010 and CSA-C22.2 No. 1010-1 Installation Category II, Working Voltage 600V
|
Automotive Accessories
|
|
|
Fluke Networks TS42DLX and TS44Pro Telephone Test Sets
|
|
Superior high-impedance monitoring
Data indication/warning
Low & high voltage indication/warning
Low current (mA) indication/warning Passive monitor
2-Way hands-free speakerphone
Low battery warning
Mute indication
Polarity indication
Tone & pulse dialing
(Optional) 1-Way amplified speakerphone mode
Amplified speaker
Last number redial
Over voltage protection
Over current protection
Mute
PBX pause button
Audible ringer
Speed dialing
Volume control... |
Telephone Test Sets / Butt Sets
|
|
|
Fluke Networks NetTool Series II Inline Network Tester
|
|
NetProve diagnostics – isolate device and application connectivity issues in seconds
Inline Gigabit vision - quickly troubleshoot network problems with powerful inline vision into 10/100/Gig traffic between switches, PCs, IP phones and other devices
NetSecure monitoring and authentication - identify spyware, malware, and viruses with port monitoring; troubleshoot authentication issues with 802.1x log
VoIP troubleshooting - connect inline for visibility into VoIP calls to quickly diagnose... |
Network Analyzers and Testers
|
|
|
Fluke CIQ-100 CableIQ Qualification Tester
|
|
Qualifies - Sees if your existing cabling has the bandwidth to support voice, 10/100, VoIP or Gigabit Ethernet
Troubleshoots - shows why existing cabling cannot support the network's bandwidth requirement (e.g. crosstalk at 11 meters)
Discovers - detects what's at the end of any cable and displays device configuration (speed/duplex/pairing)
Identifies unused switch ports that can be reallocated
Graphically maps wiring configuration and shows distance to faults with Intelligent Wiremap... |
Copper Cable Test Solutions
|
|
|
Fluke 373 True-RMS 600A/600V AC Clamp Meters
|
|
600 A ac current measurement with fixed jaw
600 V ac and dc voltage measurement
True-rms ac voltage and current for accurate measurements on non-linear signals
Resistance measurement to 6000Ω with continuity detection
1000 µF capacitance measurement
State of the art signal processing allows for use in noisy electrical environments while providing stable readings
Large, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch... |
AC Leakage Clamp Meter
|
|
|
Fluke Networks ATAP Aggregating In-Line Taps
|
|
Plug-and-play simplicity for fast analysis and deployment
Decrease budget required for visibility on redundant links
Single interface monitoring and analysis for full duplex links
Dual link models are ideal for meshed trunk analysis using single port analysis devices
Media conversion for Gigabit links expands the reach of your existing analysis solutions
Eliminates the need for spanning resources and configurations
|
Taps
|
|
|
Fluke Networks CFP-100-M CertiFiber Pro Multimode OLTS Kit
|
|
Versiv's modular design supports copper certification, fiber loss, OTDR testing and fiber end-face inspection
Taptive user interface provides simple, animated guidance to eliminate incorrect reference setup and “negative loss” errors.
Fastest time to certify – two fibers at two wavelengths in three seconds.
Encircled Flux compliant as required by ANSI/TIA and ISO/IEC with no additional test cords
Merged Tier 1 (Basic) / Tier 2 (Extended) testing and reporting when paired with... |
Fiber Certification and Testing
|
|
|
Fluke BP120MH Rechargeable Ni-Cad Battery Pack
|
|
Nominal Voltage: 4.8V
Capacity: 1800 mAh
|
Batteries, Charges and Adapters
|
|
|
Fluke Networks PTNX1 Pocket Toner Coax Cable Tester
|
|
Low voltage protection for both the main body and detachable toner unit
Dual audible indicators
Bi-gender adaptable toner section
Removable push-on connector
Removable Speed 81 connector
Lightweight, durable anodized aluminum
Auto shut off
Replaceable parts
Uses one AAA battery
One-year warranty
|
Coax Cable Testers
|
|
|
Fluke 922 and 922/Kit Airflow Meter/Micromanometer
|
|
Powerful meter provides differential and static pressure, air velocity and flow readings
Convenient colored hoses help proper interpretation of pressure readings
Easy to use without sacrificing performance
Bright, backlit display for clear viewing in all environments
User-defined duct shape and size for maximum airflow accuracy
Resolution down to 0.001 in H2O
99 point data storage capacity
Min/Max/Average/Hold functions for easy data analysis
Auto power off saves battery life
|
Air Quality Testers
|
|
|
Fluke 884X-ETH Ethernet Interface Cable
|
|
8-conductor (4 twisted pair) unshielded cable (48 inches) with an 8-position modular plug (RJ45) on each end, with an overmold boot/strain relief
Rated working voltage: 100 V rms maximum
Operating temperature range: -40 ºC to +80 ºC
|
Cables & Hardware
|
|
|
Fluke Networks JackRapid Punchdown Termination Tools
|
|
Reduces installation time - Easy-to-use tool seats and cuts all wires at once
Increases productivity – install jacks 8 times faster
Accurate, clean and consistent cuts and terminations - no more wasted jacks
Built-in bed helps hold jack in place
Eliminates user fatigue with its ergonomic handle and convenient, built-in stripper
Future proof with replaceable blade heads for use with multiple vendor jack types
Unique design easily accommodates close-to-wall installations
|
Tools and Test Kits
|
|
|
Fluke 8808A 120V, 5.5 Digital Bench Multimeter
|
|
5.5 digit resolution
Dual Display
Measures V dc/ac, I dc/ac, Ω, Freq, Continuity, Diode
Basic V dc accuracy of up to 0.015%
Min, Max, Rel, dB, dBm
2x4 Wire Ohms measurement technique
Dedicated dc leakage current ranges
Six dedicated buttons for fast access to instrument setups
Hi/Lo limit compare for Pass/Fail testing
|
Benchtop Multimeters
|
|
|
Fluke C115 Soft Carrying Case
|
|
Includes two padded pockets for protection of two test tools, such as a digital multimeter and 60 Series IR thermometer and a pouch for test leads and other accessories.
Durable polyester 600D case construction for long life.
Compatible with Fluke 20, 70, 11X, 170 Series digital multimeters and other similar format test tools.
One-year warranty.
|
Cases and Holsters
|
|
|
Fluke 700-IV Current Shunt
|
|
Very accurate current shunt to use for verification and calibration of process control loops.
Can be used with accurate voltmeters for calibration purposes
Can be used with Fluke 74X series in mA/mA applications (74X will display mA/mA automatically) One year warranty
|
Connectors
|
|
|
Fluke 705 Loop Calibrator
|
|
A large display and simple, pushbutton interface for ease of use.
Simultaneous mA and % readout for quick, easy interpretation of readings.
mA accuracy of 0.02%
Push button 25% steps for fast, easy linearity checks. Save time over traditional knob type controls.
"Span Check" for fast confirmation of zero and span.
Selectable slow ramp, fast ramp, and step to provide smooth outputs for valve slewing and loop functional tests.
24 volt internal loop supply, so you can power and read a... |
Calibrators
|
|
|
Fluke 80i-110s AC/DC Current Clamp
|
|
Current Range: 0.1 to 100A DC or 0.1 to 70A AC
Basic Accuracy (DC to 1kHz):
100mV/A setting: 50mA to 10A +/- 3% of reading + 50mA
10mV/A setting: 50mA to 40A +/- 4% of reading + 50mA40A to 80A +/- 12% of reading + 50mA80 to 100A +/- 15% of reading
Output Signal: 10A range: 100mV/A | 100A range: 10mV/A
Bandwidth: 1Hz to 20kHz
Working Voltage: 600V AC rms
Maximum Conductor Size: 1.8 mm (.46 inch) diameter
Safety Rating: IEC 1010 and CSA-C22.2 No. 1010-1 Installation Category II,... |
Current Clamps
|
|
|
Fluke Priority Gold Instrument CarePlan For Thermal Imagers
|
|
Repairs are always unexpected, and they can be costly. Keep your camera in top operating condition and control your cost of ownership with a Fluke Gold CarePlan. Maintain you camera in peak operating condition and protect your investment beyond your factory warranty for up to three additional years. |
CarePlans & warranties
|
|
|
Fluke FOM Fiber Optic Meter
|
|
The compact FOM plugs into your DMM and makes testing in tight spaces easy
A variety of light sources (FOS 850, FOS 1300, and FOS 850/1300) and patch cords (ST to ST, ST to FC, ST to SC, ST to SMA) let you get just what you need for testing different cable types and lengths
Highly accurate readings mean less work, less repeated testing
Input connector: fixed ST
Battery life: 16 hours minimum, 9V alkaline
LED low battery indicator
Operating temperature: 0°C to +40°C (32°F to... |
Fiber Optics
|
|
|
Fluke 62 Max+ Infrared Thermometer with Dual-point Laser Sighting 30°C to 650°C, 12:1 ratio, ±1% Accuracy
|
|
Wide temperature range from -30° to 650°C (–20° to 1202°F)
12:1 distance-to-spot ratio
±1% Accuracy of the reading.
Dual lasers to accurately identify spot size
Rugged performance
Survives 9.8 foot/3 meter drops to wood floors
Water and dust resistance
IP54 rated to withstand rain, splashing liquids, dust and dirt
Small and easy to use
Ergonomic fit to "feel" good in your hand
Multi-angle
Backlit display
|
Combo Test Kits
|
|